Volvo Forums banner
1 - 16 of 16 Posts

· Registered
Joined
·
7 Posts
Discussion Starter · #1 ·
New member here, I'm parting out my grandfather's 1975 Volvo 164E. Sold some parts already, so some of the stuff isn't there anymore, used some parts on other projects too.

Alot of good sheetmetal/body panels (ie : fenders, hood, doors, quarter panels, ect) Although the hood has a small hole rusted in the one corner where my grandfather had a CB Antenna mounted. And some areas of the car have rusted out spots/holes (rocker panels i beleive, and the Rear Inner Wheelwells)

Most of the Glass (minus the Driver's Side Rear, where some kids busted the window out)

Engine, Transmission, Rear Differential, suspension, ect.


--
Off the top of my head, the stuff that is no longer on the car (either sold or used in one of my projects) :

Seats, Front & Rear (used them in my 1974 Plymouth Duster)
Fuel Injectors & Throttle Body (sold)
MAP Sensor (sold)
Instrument Cluster & also the Clock (with bezel, sold)
Relays (sold)
Headlight Rings/Bezels (sold)
Door Handles (sold)
Exterior/Door Mirrors (sold)
bunch of other small stuff i'm forgetting.

--
The engine ran when the car was parked (quite a few years ago), after some kids vandalized the car. It had about 115,000 miles on it and the Automatic Transmission shifted great. It has the B30E Fuel Injected Inline-6 Cylinder Engine & 3-Speed Automatic Transmission.

I have some of the parts on shelves in the garage, other parts are still on the car, minus whatever was already used/sold.

I hope to find the time in October to load the car on my Rollback and bring it up to the garage so i can strip it down (it's still parked at my grandfather's house at the moment)

So if you're looking for something, let me know.
 

· Registered
Joined
·
330 Posts
I'm still looking for a charcoal cannister. I was looking at the parts lists here Webbshop and there seems to be some common emmissions parts between '70s Volvos.

What I want looks like a short, Heinz tomato juice can, about 6" in diameter with two vaccum hose fittings in the top.

Let me know if you've got something.
 

· Registered
Joined
·
7 Posts
Discussion Starter · #4 ·
duster where is car also live in pa and would like to look at car for parts?
You have a message ;), i can get pictures if its too far of a drive for you.

--

Bhart, the EVAP / Charcoal Canister should still be on the car (i don't remember removing it). I'll check this weekend (maybe sooner) when i go over to my grandfather's house to fix his tv.
 

· Registered
Joined
·
7 Posts
Discussion Starter · #8 ·
No, just the cannister.
Alrighty.

I'll get a picture of the Canister for you, and remove it from the car. Yoyo wanted to see the Rocker Panel (passenger side).

I'll get the pictures tomorrow, i don't think i'll be hauling it home saturday. It started snowing here (my rollback is 2wd), and it's supposed to continue into saturday night. But that won't stop me from removing the canister for you and getting those pictures.
 

· Registered
Joined
·
7 Posts
Discussion Starter · #9 ·
Sorry for the Double Post, but here's the pictures. It took me a little longer than i promised to get them though.

Here's the Charcoal Canister


And here's the pictures of the Rocker Panel for Yoyo (there is one hole right below the trim, i got a close up picture of the hole for you.)

 

· Registered
Joined
·
330 Posts
Thanks for the pic of the cannister, but it's too new!

I want to keep things original, so I'll keep searching.

BTW, if that's the only rust, that car is great!
 
1 - 16 of 16 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top